Laser Cutter

Machine Information

• Owner: Backyard Brains
• Who Can Use: Roger S., Josh W., and Zach S. currently have experience running this LASER. Greg G., and Tim M. purchased it. Accordingly, they can do whatever they want with it ; )

Status: Temporarily Operational

• The machine is up and running, but we lack:
  • Permanent filtering/ventilation
  • Documentation
  • Price info

Josh Williams is currently the primary contact for the installation process.

Usage Information

1) Turn on Power strip next to the computer, that should turn the chiller on which should make a horrible beep noise for 5-10 seconds. 2) Turn on the computer. 3) Turn on the LASER Cutter (you will need a key, currently located in the LASER Cutter Toolbox above the LASER Cutter computer 4) Turn on the Filter (temporarily located in the boiler room behind the laser cutter) 5) Turn on the Blower (temporarily located in the boiler room behind the laser cutter) 6) Launch "LASERCut 5.3"

Steps to get it running

• Reconnect electronics (disconnected during leg removal)
• Go over LASER cutter, compare with manual.
• Install Tube
• Connect power to LASER Cutter: Boots
• Connect Air Compressor to LASER: Working
• Connect power to Chiller, connect alarm cable to laser: Works
• Test Jogging X/Y/Z
• Super brief test firing: Works
• Align Mirrors
• Figure out placement of computer/monitor
• Install lasercut software & test connection to laser
• Remove Metal Cutting Board (below honeycomb)
• Fix hood closing issue (catches on right side)
• Install hood handles
• Organize Air & Water Tubing
• Mount Air Compressor to floor
• Where is hole for ventilation?
• Where to exhaust to?
• How much to exhaust out of building (top)
• Filter?

Notes specific to the install at AHA

• Water Chiller installed underneath laser. Pull laser forward ~4' in order to access. Be careful to avoid crushing or pulling out tubes for air & water
• Air Compressor installed underneath laser. Pull laser forward ~4' in order to access. Be careful to avoid crushing or pulling out tubes for air & water
• Currently two power strips are utilized, each connected to a separate circuit
  • The laser itself connects to the red spray painted outlet. This circuit is accessible from two other places within AHA. This should be avoided!
  • The Computer and Water chiller connect to the outlet adjacent to the red spray painted outlet. The blower will also likely be connected to this outlet

What was Ordered

Jinan TransonCNC 1490A in a 1490B shell. (It comes apart easier for the purpose of fitting through our front door)

• We have been told that everything is outfitted to run on standard 120ac (LASER Cutter, Chiller/Pump, and Exhaust)
• LASER Power Reci80W
• Weight: ~450 kg (1000 lbs)
• Equipment Dimension Top Half 192*131*42cm
• Equipment Dimension Bot Half 192*131*70cm
• Working Area 140cm*90cm
• Metal Slat Table
• Motorized up and down table
• honeycomb table
• Red Dot pointer
• Auto Focus
• Extra Reci80W (LASER Tube)
• Extra Lens & Mirror
• Extra Motion Card (Controller)
• Extra Belt - X Axis
• Extra Belt - Y Axis
• Extra Motorized up and Table Belt
• Extra Girdle Belt
• Extra X Motor
• Extra Y Motor
• Extra Z Motors (2)
• LASER Goggles
• CW3000 Water Chiller

Exhaust

• Exhaust Port: 6"
• CFM ~512

Manuals

• Software Manual: https://drive.google.com/file/d/0B9x4RIcqwUojamYxMkswT3EwUWtFVWpwMHpZM0ZRN2hyRFdr/edit?usp=sharing
• Machine Manual: https://drive.google.com/file/d/0B9x4RIcqwUojbm5tdzI2ZnFmV291anZBS0RaZGlOVXQweUZz/edit?usp=sharing

Ongoing Maintenance Costs

Regularly Recurring

• Filters
• Activated Charcoal?
• de-ionized water
• LASER Tubes

Occasional

• Replacement Hardware on LASER (Motors, Belts, etc.)

Ongoing Maintenance

• Who is responsible for the work?
• Who is responsible for the costs?

Training

• TBD once we have the machine. See the manuals linked above for "What we know now"