Laser Cutter

Machine Information

• Owner: Backyard Brains
• Who Can Use: Roger S., Josh W., and Zach S. currently have experience running this LASER. Greg G., and Tim M. purchased it. Accordingly, they can do whatever they want with it ; )

Status: Temporarily Operational

• The machine is up and running, but we lack:
  • Permanent filtering/ventilation
  • Documentation
  • Price info

Josh Williams is currently the primary contact for the installation process.

General usage information

Turning everything on

1. Turn on the Power strip next to the computer
   1. This should turn the chiller on which makes a beeping noise for 5-10 seconds.
   2. If you don't hear a beeping noise, something is wrong. Please stop here.
2. Turn on the computer
3. Turn on the LASER Cutter using the laser key.
   1. Key is located in the laser cutter toolbox above the laser computer.
      1. The bed of the laser should light up, if not there is an on off switch on the side of the laser to below the control panel.
4. Turn on the Filter (temporarily located in the boiler room behind the laser cutter)
5. Turn on the Blower (temporarily located in the boiler room behind the laser cutter)

File prep & loading your material

1. On the computer, launch "LASERCut 5.3" from the desktop
2. Place the material you are cutting towards the center of the laser bed
   1. If the bed is too high, use the "Z-" within the lasercut software to lower the bed.
3. Use the x and y panel within the Lasercut software to position the laser head at the top left corner of your object
4. Use the "Z Dataum" button on the computer to set the laser at the right height.
   1. The laser must be positioned on top of your material for this to work accurately
5. Adjust your speed & power settings in the top right hand corner in accordance to your needs.
   1. This has not been covered yet.
6. Set the laser origin to "top left" by:
   1. Select everything (Ctrl-A)
   2. Tools Menu -> Set laser origin
   3. Check "Relative to Selection" and choose "Left-top"
7. Select the "Pick" mouse cursor tool
   1. Make sure your design is still selected
   2. Hit the Space Bar
   3. Select "Left-top"

Test

1. When you have everything setup, click "Download"
   1. Select "Download Current" to load your design on to the laser cutter
   2. Select "Run Box" to do a perimeter test.

Burn

1. Double check to make sure the filter, blower, and chiller are on.
2. Click "Start" to begin your burn.
3. Do not leave the laser cutter while your burn is going

File Prep

With your file open in lasercut 5.3:

Other stuff:

1. Remember to download your file before doing the "Run Box" perimeter test
2. Tape your object down if it's light (ie: paper)
3. Select everything in your file and click "Unite Lines".

Interesting Issues

1. When running an outline of a Moai head, the laser stopped and started at various points for a very brief moment.
   1. We simplified the outline in inkscape and made sure to unite lines in lasercut 5.3. This helped, but we still stop/start problems with the laser.
2. It appears that if your image/vector file is greater than any dimension of the bed (140cm * 90cm), the software will crash upon opening.

Steps to get it running

• Reconnect electronics (disconnected during leg removal)
• Go over LASER cutter, compare with manual.
• Install Tube
• Connect power to LASER Cutter: Boots
• Connect Air Compressor to LASER: Working
• Connect power to Chiller, connect alarm cable to laser: Works
• Test Jogging X/Y/Z
• Super brief test firing: Works
• Align Mirrors
• Figure out placement of computer/monitor
• Install lasercut software & test connection to laser
• Remove Metal Cutting Board (below honeycomb)
• Fix hood closing issue (catches on right side)
• Install hood handles
• Organize Air & Water Tubing
• Mount Air Compressor to floor
• Where is hole for ventilation?
• Where to exhaust to?
• How much to exhaust out of building (top)
• Filter: We are testing the RSU 20CCHR Electrocorp

Notes specific to the install at AHA

• Water Chiller installed underneath laser. Pull laser forward ~4' in order to access. Be careful to avoid crushing or pulling out tubes for air & water
• Air Compressor installed underneath laser. Pull laser forward ~4' in order to access. Be careful to avoid crushing or pulling out tubes for air & water
• Currently two power strips are utilized, each connected to a separate circuit
  • The laser itself connects to the red spray painted outlet. This circuit is accessible from two other places within AHA. This should be avoided!
  • The Computer and Water chiller connect to the outlet adjacent to the red spray painted outlet. The blower will also likely be connected to this outlet

What was Ordered

Jinan TransonCNC 1490A in a 1490B shell. (It comes apart easier for the purpose of fitting through our front door)

• We have been told that everything is outfitted to run on standard 120ac (LASER Cutter, Chiller/Pump, and Exhaust)
• LASER Power Reci80W
• Weight: ~450 kg (1000 lbs)
• Equipment Dimension Top Half 192*131*42cm
• Equipment Dimension Bot Half 192*131*70cm
• Working Area 140cm*90cm
• Metal Slat Table
• Motorized up and down table
• honeycomb table
• Red Dot pointer
• Auto Focus
• Extra Reci80W (LASER Tube)
• Extra Lens & Mirror
• Extra Motion Card (Controller)
• Extra Belt - X Axis
• Extra Belt - Y Axis
• Extra Motorized up and Table Belt
• Extra Girdle Belt
• Extra X Motor
• Extra Y Motor
• Extra Z Motors (2)
• LASER Goggles
• CW3000 Water Chiller

Exhaust

• Exhaust Port: 6"
• CFM ~512

Manuals

• Software Manual: https://drive.google.com/file/d/0B9x4RIcqwUojamYxMkswT3EwUWtFVWpwMHpZM0ZRN2hyRFdr/edit?usp=sharing
• Machine Manual: https://drive.google.com/file/d/0B9x4RIcqwUojbm5tdzI2ZnFmV291anZBS0RaZGlOVXQweUZz/edit?usp=sharing

Ongoing Maintenance Costs

Regularly Recurring

• Filters
• Activated Charcoal?
• de-ionized water
• LASER Tubes

Occasional

• Replacement Hardware on LASER (Motors, Belts, etc.)

Ongoing Maintenance

• Who is responsible for the work?
• Who is responsible for the costs?

Training

• TBD once we have the machine. See the manuals linked above for "What we know now"