Laser Cutter

From All Hands Active Wiki
Jump to navigation Jump to search

Machine Information

  • Owner: Backyard Brains
  • Who Can Use: Roger S., Josh W., and Zach S. currently have experience running this LASER. Greg G., and Tim M. purchased it. Accordingly, they can do whatever they want with it ; )

Status: Temporarily Operational

  • The machine is up and running, but we lack:
    • Permanent filtering/ventilation
    • Documentation
    • Price info

Josh Williams is currently the primary contact for the installation process.

Usage Information

  1. Turn on Power strip next to the computer,
    1. This should turn the chiller on which makes a beeping noise for 5-10 seconds.
    2. If you don't hear a beeping noise, something is wrong. Please stop here.
  2. Turn on the computer.
  3. Turn on the LASER Cutter (you will need a key, currently located in the LASER Cutter Toolbox above the LASER Cutter computer
    1. The bed of the laser should light up, if not there is a on off switch on the side of the laser to below the control panel.
  4. Turn on the Filter (temporarily located in the boiler room behind the laser cutter)
  5. Turn on the Blower (temporarily located in the boiler room behind the laser cutter)
  6. On the computer, launch "LASERCut 5.3" from the desktop.
  7. Open or create your file that you wish to lasercut. This document does not currently cover how to do this
  8. Place the item you are cutting on the laser bed
    1. If the bed is too high, use the "Z" within the lasercut software to lower the bed.
  9. Use the x and y panel with the lasercut software to position the laser head above your object
  10. Use the "Z Dataum" button on the computer to set the laser at the right height
  11. When you have everything setup, click "Download" and choose "Download Current" to load it on to the laser cutter
    1. double check to make sure filter/blower/chiller are on.
    2. Click "Start" to fire

Other stuff:

  1. Remember to download your file before doing the "Run Box" perimeter test
  2. Tape your object down if it's light (ie: paper)
  3. Select everything in your file and click "Unite Lines".

Steps to get it running

  • Reconnect electronics (disconnected during leg removal)
  • Go over LASER cutter, compare with manual.
  • Install Tube
  • Connect power to LASER Cutter: Boots
  • Connect Air Compressor to LASER: Working
  • Connect power to Chiller, connect alarm cable to laser: Works
  • Test Jogging X/Y/Z
  • Super brief test firing: Works
  • Align Mirrors
  • Figure out placement of computer/monitor
  • Install lasercut software & test connection to laser
  • Remove Metal Cutting Board (below honeycomb)
  • Fix hood closing issue (catches on right side)
  • Install hood handles
  • Organize Air & Water Tubing
  • Mount Air Compressor to floor
  • Where is hole for ventilation?
  • Where to exhaust to?
  • How much to exhaust out of building (top)
  • Filter: We are testing the RSU 20CCHR Electrocorp

Notes specific to the install at AHA

  • Water Chiller installed underneath laser. Pull laser forward ~4' in order to access. Be careful to avoid crushing or pulling out tubes for air & water
  • Air Compressor installed underneath laser. Pull laser forward ~4' in order to access. Be careful to avoid crushing or pulling out tubes for air & water
  • Currently two power strips are utilized, each connected to a separate circuit
    • The laser itself connects to the red spray painted outlet. This circuit is accessible from two other places within AHA. This should be avoided!
    • The Computer and Water chiller connect to the outlet adjacent to the red spray painted outlet. The blower will also likely be connected to this outlet

What was Ordered

Jinan TransonCNC 1490A in a 1490B shell. (It comes apart easier for the purpose of fitting through our front door)

  • We have been told that everything is outfitted to run on standard 120ac (LASER Cutter, Chiller/Pump, and Exhaust)
  • LASER Power Reci80W
  • Weight: ~450 kg (1000 lbs)
  • Equipment Dimension Top Half 192*131*42cm
  • Equipment Dimension Bot Half 192*131*70cm
  • Working Area 140cm*90cm
  • Metal Slat Table
  • Motorized up and down table
  • honeycomb table
  • Red Dot pointer
  • Auto Focus
  • Extra Reci80W (LASER Tube)
  • Extra Lens & Mirror
  • Extra Motion Card (Controller)
  • Extra Belt - X Axis
  • Extra Belt - Y Axis
  • Extra Motorized up and Table Belt
  • Extra Girdle Belt
  • Extra X Motor
  • Extra Y Motor
  • Extra Z Motors (2)
  • LASER Goggles
  • CW3000 Water Chiller


Exhaust

  • Exhaust Port: 6"
  • CFM ~512


Manuals


Ongoing Maintenance Costs

Regularly Recurring

  • Filters
  • Activated Charcoal?
  • de-ionized water
  • LASER Tubes

Occasional

  • Replacement Hardware on LASER (Motors, Belts, etc.)

Ongoing Maintenance

  • Who is responsible for the work?
  • Who is responsible for the costs?

Training

  • TBD once we have the machine. See the manuals linked above for "What we know now"